I’ve used it on a machine before but given I am using a cloudflared container for ingress, can I route my traffic through a f2b container to the app? This might be ideal from a co fig perspective.
LLMs say yes but I’ll need to play around.
I have more than 50k but even that page doesn’t recommend it.
Top of that page
Recommendation: Use WAF custom rules instead
Cloudflare recommends that you create WAF custom rules instead of IP Access rules to perform IP-based or geography-based blocking (geoblocking):
- For IP-based blocking, use an IP list in the custom rule expression.
On the fail2ban front, can I run my traffic through a f2b container and out into my app?
How easy is it to configure?
My goal is to download some lists from github and generate one big ban list to feed into the WAF but the community lists of Crowdsec might negate the need.
I use namesilo for everything but my .au domains.
Sometimes I miss my r720s but the silence is nice now.
Xcp or proxmox as your os.
720 depending on chips and memory is great for game servers.
I didn’t think OP was going the ZFS route so it wouldn’t matter on that point.
His Server 2 will be running on the red line imho so any overhead would have impact.
Mount your NFS in the fstab and make sure you have docker set to wait until the mount is working. Here is a guide. https://davejansen.com/systemctl-delay-start-docker-service-until-mounts-available/
I’ve only had to delay on my N100s.
So I have the mounts set and then just use those paths in my compose. All my machines have the same paths.
quicksync should let the i3 handle jellyfin just fine if you’re not going beyond 1080p for a couple of concurrent users. Especially if you configure the Nice values to prefer jellyfin over immich.
Most of my content is 4K h264. You may be right on the 1080 but I don’t have content at that resolution generally.
Worst case scenario he can always keep the N300 for other stuff if it doesn’t work out.
I’ve looked at it but never actually given the Synology proxy a go despite using their DNS server. Does it do auto certificate renewal?
Have you considered using a Cloudflare tunnel to bypass the CGNAT? You can do that into a proxy or straight into the service.
That would be a smart move on their behalf I think.
Might be the population on lemmy but elsewhere docker or podman are way more common. K8 in Enterprise.
I ran Jellyfin on a N100 for a while and it just couldn’t cope despite being by itself on the machine. I mostly watch 4K h264 encoded stuff. I ended up putting it on a machine with an i5.
All the services OP has listed run great in docker, excluding Frigate (not tested personally).
Or just run them in containers and skip the need to run the VMs at all. You can do snapshots with Debian fine.
Personally I would keep it simple and just run a separate NAS and run all your services in containers across the devices best suited to them. The i3 is not going to manage for Jellyfin while sharing those other services. I tried running it on an N100 and had to move it to a beefier machine(i5). Immich for example will use a lot of resources when peforming operations, just a warning.
If you mount a NAS storage for hosting the container data, you can move them between machines with minimal issues. Just make sure you run services using a docker-compose for them and keep them on the NAS.
You completely negate the need for VMs and their overhead, can still snapshot the machine if you run debian as the OS there is timeshift. Other distros have similar.
So I recently sandboxed a webapp I am getting ready to launch.
Basically Unifi switch > Vlan port > Server > Hosting Webapp instances, worker instance, cloudflared and DBs.
Pretty chuffed at the docker config actually. Just configuring my WAF and tunnel settings with Cloudflare to reduce the scanning from VPS providers. Anyone have a solution or will I need to configure some sort of nginx instance to do it as Cloudflare only allows a certain length for each WAF rule for free.
Side thought, does anyone know of a tutorial for CICD to auto build my containers and deploy? I’ve been reading github and codeberg docs and playing around to no avail. I’m temped to just write a go script to handle it on my server.
Not all heroes wear macros.
I’ve done BYO TrueNas and unraid and eventually went for a pair of 8 Bay Synology NAS for bulletproof hardware and ootb working backups, replication etc.
I run containers on machines that also use the NFS storage supplied by them.
Ahhhmazing, I’ll set this up tonight. Really appreciate the help.